K-LQP cross-linked cable slicing machine maintenance method Suzhou Keitel equipment manufacturers specializing in the production of: cross-linked cable slicing machine, cable sample flanging machine, insulation jacket punching machine, wire winding and torsion testing machine, cable and three-wheel flexural testing machine, tensile testing machine, universal test Machine and so on. Medical Components,Plastic Injection Molding Parts,Molded Plastic,Abs Plastic Parts Ningbo Yongsheng Rubber And Plastic Products Co., Ltd. , https://www.yscnrubber.com
The instrument complies with GB/T11017 "The 110kV rated cross-linked polyethylene insulated power cable and its accessories", GB/T12706 "The rated voltage 1kv-35kv extruded insulated power cable and accessories", GB/T2951.11-2008, GB/ T2951.1-1997 "General Test Method for Cable Insulation and Sheath Materials" standard. Supporting the completion of the thermal extension test and tensile test. Especially suitable for longitudinal and lateral sampling of mechanical and physical properties of cross-linked polyethylene cables.
A cross-linked cable slicing machine using instructions
1. Check whether the equipment is intact after unpacking the equipment. If it is deformed or damaged during transportation, please contact your local dealer.
2. Cross-sectional sampling of cross-cable slicing machine (first remove the bow clip on the longitudinal fixture with a spanner)
2.1. After turning on the power, turn on the power switch. The red light indicates that the power is normal. Press the left arrow button to move the cutter to the left of the left fixture. Open the left and right two fixtures and take the cable sample 300-400mm on the fixture. The flat, rotating clamp handwheel clamps the cable specimen.
2.2. Rotate the handwheel to adjust the height of the cutting tool so that the front plate of the knife holder presses the sample (the thickness of the sample is adjusted, and the effective range of the sample is 0.2mm-2mm). Then press the right direction button and the cutting edge will be in the axial direction. Trim the test piece and press the stop button to stop the machine.
2.3. If you find uneven slicing or tailing, press the left arrow button to repeat slicing or loosen the four screws on the knife holder to adjust the cutting edge length of the tool.
3 Cross-linked cable slicing machine. Vertical sampling
3.1. Raise the knife holder first and fix the bow fixture to the top of the longitudinal fixture. Take a 5cm-10cm sample vertically and clamp it in the longitudinal fixture. The sample is out of the bow fixture 1mm-2mm, then press work. Button to plan the test piece.
4, the blade should be out of the knife when the bottom 2mm
5, on the cut directly with the lower edge of the cutting tool, the sample is clamped in the lateral sampling fixture, adjust and open the right switch to open the sample, do not let the cut tool cut to the conductor, so as not to damage the tool blade
7. Remove the cutting tool when slicing.
8. Do not cut metal objects and have damaged cutter blades;
Second, cross-linked cable slicing machine maintenance
1. After use, cut off the power supply, cover with a dust cover, and lubricate part of the oil regularly to maintain lubrication.
2. Do not put metal and hard objects into the cutting port to cut the damaged blades.
Suzhou Keitel equipment manufacturers specializing in the production of: ultraviolet aging test chamber, ozone aging test chamber, xenon lamp aging test chamber, high and low temperature test chamber, constant temperature and humidity chamber, aging test chamber, ventilation aging test chamber, natural ventilation aging test chamber, etc. .
Third, cross-linked cable slicing machine main parameters
1, the maximum working width 400mm
2. Cross section thickness 0.2mm-10mm
3, transverse test strip width 10mm-70mm/10-150mm
4, longitudinal test piece diameter 10mm-70mm (ibid.)
5, motor power 0.37kw/0.75kw, 1500r/min
6, rated voltage AC220V/50HZ
7, the machine dimensions 880×540×1100
8, weight (approx) 150kg
The other dimensions and parameters can be customized according to customer requirements.