CNC Intelligent Automatic High Speed Glass Cutting Line has been comprehensively upgraded by means of introduction of European leading technology, world newest tech and process to eliminate the insufficient performances, incomplete functions and unstable operation from domestic glass loader, moreover,through the precise racks, slide-rails, servo motors and pneumatic elements, it achieves the long-term stable accuracy and fast running with the newest American Galil control system, it features even faster operation, higher safety, higher efficiency, more stability and better accuracy: with the photoelectric positioning, it facilitates the simple and precise operation and prominent labor saving
Glass Cutting Machine,Glass Cutting Table,Automatic Glass Cutting Machine,Cnc Glass Cutting Machine JINAN KATION TRADING CO.,LTD , https://www.machinerychinese.com
Corrugated pipe safety valve adjustment technology operation flow
1) Opening the pressure adjustment ①safety valve factory, it should be adjusted one by one to its pressure to the user set the desired value. If the user puts forward the working pressure level of the spring, the factory should be adjusted according to the lower limit of the pressure level. ② Before installing the safety valve on the equipment to be protected or before installation, the user must re-adjust the installation site to ensure that the setting value of the safety valve meets the requirements. (3) Within the range of the spring working pressure indicated on the nameplate, the opening pressure can be adjusted by rotating the adjusting screw to change the amount of spring compression. ④ Before rotating the adjusting screw, the inlet pressure of the valve should be reduced to less than 90% of the opening pressure to prevent the valve disc from being rotated when the adjusting screw is rotated, so as to damage the sealing surface. ⑤ In order to ensure that the opening pressure value is accurate, the media conditions, such as the type and temperature of the medium, should be adjusted as close to the actual operating conditions as possible. Changes in the type of media, especially when the media is not the same state of accumulation (for example, from liquid to gas phase), the cracking pressure often varies. Operating temperature increases, the opening pressure is generally reduced. Therefore, when adjusted at room temperature for high temperature, the setting pressure at room temperature should be slightly higher than the required opening pressure. To what extent and the valve structure and material selection are related, should be based on the manufacturer's instructions. ⑥ conventional safety valve for fixed additional back pressure occasions, when the test is adjusted to open pressure (back pressure at this time atmospheric pressure), the setting value should be required to open the pressure value minus the additional back pressure value. (2) Adjustment of discharge pressure and back pressure (1) To adjust the discharge pressure and back pressure of the valve, it is necessary to perform the operation test of the valve to reach the fully open height. Therefore, only when the test device with large capacity Or after the safety valve is installed on the protected equipment. The adjustment method according to the valve structure is different. ② For the structure with recoil plate and seat adjusting ring, the seat adjusting ring is used for adjustment. Unscrew the adjusting ring fixing screw, extending from the exposed screw hole a thin iron rod and the like tools, you can dial the gear ring on the adjustment ring, the adjustment ring around. When the adjustment ring to the left counterclockwise rotation, its position increased, the discharge pressure and the seat back pressure will be reduced. Conversely, when the adjustment ring is rotated clockwise to the right, its position is lowered and both the discharge pressure and the seatback pressure are increased. Each adjustment, the adjustment: circle rotation range should not be too large (generally rotate the number of teeth can be). After each adjustment, the fixing screw should be screwed up so that the end is located in the groove between two teeth of the adjusting ring, so as to prevent the adjusting ring from rotating without generating radial pressure on the adjusting ring. For safety reasons, the dial should be adjusted before adjusting the pressure relief valve should be appropriate to reduce the pressure (generally should be less than 90% of the opening pressure) to prevent the valve suddenly opened in the adjustment, causing an accident. ③ For the upper and lower adjustment ring (guide sleeve and valve seat each have a regulation ring) structure, the adjustment to be more complex. The seat adjusting ring is used to change the size of the passage between the valve flap and the adjusting ring so as to change the pressure accumulation in the cavity between the valve flap and the adjusting ring when the valve is initially opened. When the valve seat adjusting ring is raised, the degree of pressure build-up increases, so that the phase of valve opening is reduced and the sudden snap-on is reached quickly. Therefore, raising the seat ring can reduce the discharge pressure. It should be noted that the seat ring can not be raised too close to the valve flap too close. In that case, the leakage at the sealing surface may cause the valve to suddenly open prematurely, but because of the medium pressure is not enough to keep the valve in the open position, the valve flap then closed again, so the valve frequency hopping. Seat adjustment: "The ring is mainly used to reduce the valve ratio, open the stage and adjust the discharge pressure, but also have an impact on the seatback pressure. (3) lead seal safety valve is adjusted, should be sealed, to prevent casual change has been adjusted to good condition. When repairing the safety valve, note the positions of the adjusting screw and adjusting ring before disassembling the valve to facilitate the adjustment work after the trimming. After re-adjustment should be sealed again.